STEP PLUMBING GUIDE FOR INSTALLING A BATHTUB

Step Plumbing Guide for Installing a Bathtub

Step Plumbing Guide for Installing a Bathtub

Blog Article

Website

The writer is making a number of great annotation on Installing A Bathtub in general in this post underneath.


Installing A Bathtub
Installing a bathtub isn't specifically brain surgery, however it does call for strong plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a new one is likewise a moderately challenging job. If the old bathtub is conveniently easily accessible, the task can relocate immediately; if you have to open a wall surface to get rid of the old tub as well as position the brand-new bathtub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will require an assistant to vacate the old bathtub as well as embeded in the new one. Make sure you have actually certified yourself for the task and are comfortable trying it. Rather than employing a professional to take control of a halfway-completed task, it is far better to consider utilizing one prior to you start. Chances are you may need a specialist plumber to make tube links.
This article will certainly help you install a new tub in your shower room if you have actually already purchased a brand-new tub and do not require to transform the arrangement of your previous water system pipelines.
Your devices as well as product checklist ought to comprise the following:
  • New Bathtub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Removing Old Touches


    If you need to change old faucets with brand-new ones as a part of your installment, after that the first thing you ought to do is detach the water. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of removing the existing taps can be fairly bothersome due to the restricted access that is frequently the case.
    Make use of a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that connects the supply pipelines to the taps. Have a fabric all set for the staying water that will certainly originate from the pipes. When the supply pipelines have actually been removed, make use of the very same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from turning during this process. Once the taps have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
    Before carrying on to fit the new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is needed for the new faucets to fit.

    Fitting New Touches


    If the tails of the new faucets are plastic, then you will require a plastic port to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a connection to the existing supply pipelines.
    If you need to fit a monobloc, after that you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
    Next off, position the tap in the mounting hole in the bath/basin making sure that the washing machines remain in location between the tap and also the sink. Safeguard the tap in place with the manufacturer given backnut. Once the faucet is securely in place, the supply pipes can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal tap connectors. The previous kind should be linked to the tap finishes initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Mounting the Bath tub


    Utilizing the two wooden boards under its feet, position the bathtub in the called for position. The wooden boards are helpful in equally spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 little points.
    The next goal is to make sure that the tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bathtub until the spirit level checks out level.
    To mount taps, fit the bottom of the furthest adaptable tap port to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
    Turn on the water as well as inspect all joints and new pipework for leaks and tighten them if needed. Fill up the bathtub and additionally check the overflow outlet and also the typical outlet for leaks.
    Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and securing around the tub should wait till the tub has been utilized a minimum of once as this will resolve it into its last position.

    Planning for the Setup


    Firstly, the supporting framework provided with the bath must be fitted (if called for) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
    Fit the adaptable faucet ports to the bottom of both taps making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next, fit the end of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
    Attach the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should now prepare to be fitted in its final placement.

    Tiling Around the Bath tub


    In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can move enough to break a stiff seal, triggering the water to permeate the wall in between the bath and also the tiling, bring about problems with wetness and feasible leaks to the ceiling below.
    You can pick from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are offered in tubes and also cartridges, and are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to constantly fill the tub with water before sealing, to enable the motion experienced when the bathtub is in use. The sealant can break relatively early if you do not think about this movement before sealing.
    Alternatively, ceramic coving or quadrant tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to dimension, are additionally easily offered on the market. It is a good idea to fit the ceramic tiles using waterproof or water-proof sticky and cement.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Installing A Bathtub

    We were shown that article about A Step-by-Step Guide to Installing a Bathtub through a good friend on another blog. Remember to take the opportunity to distribute this blog if you enjoyed reading it. We enjoy reading our article about Installing A Bathtub.


    Book Inspection

    Report this page